中空玻璃生产线的故障其时是很少的，我们在判断电与气路方面的故障时先采用手动方式进行检查，再根据实际发生情况来解决问题。
there are very few faults in the insulating glass production line at that time. when judging faults in the electrical and gas circuits, we first use manual inspection, and then solve the problem based on the actual situation.
a.故障：板压进入第一块玻璃后，侧定位没有起来，玻璃出来一部分后在板压内停止。板压不压合。 原因：板压计数开关未计上数。
a. fault: after the board enters the first glass, the side positioning does not rise, and a portion of the glass comes out and stops inside the board. the plate does not press properly. reason: the board pressure counting switch did not count.
b.故障：板压进入第一块玻璃后，侧定位没有起来，玻璃出来一部分后在板压内停止。板压压合，下定位托起。原因：手动检查侧定位是否起做用。
b. fault: after the board enters the first glass, the side positioning does not rise, and a portion of the glass comes out and stops inside the board. press and press the plate together, and lift it in the lower position. reason: manually check if the side positioning is working.
c.故障：板压进入第一块玻璃后，侧定位没有起来，玻璃出来一部分后板压输送轮未停止。原因：检查板压内检测开关。
c. fault: after the plate is pressed into the first piece of glass, the side positioning does not rise, and the plate pressing conveyor wheel does not stop after a portion of the glass comes out. reason: check the internal pressure detection switch of the board
d.故障：板压进入第一块玻璃后，压合完后不回来，未听到吸盘吸合的声音。原因：检查板压里面的最小区域微动开关。
d. fault: after the plate is pressed into the first glass, it does not come back after pressing, and the sound of the suction cup is not heard. reason: check the micro switch in the minimum area inside the board pressure.
e.故障：1800丝杠型生产线在回参过程是到位不停止。原因：丝杠线回参一定要先将板压张开过板压减速开关点，再进行回参。检查在回参过程中回参点与减速点的接近开关是否有信号。
e. fault: the 1800 screw type production line does not stop during the reference process. reason: the screw thread must first open the plate pressure and pass through the plate pressure deceleration switch point before returning to the reference. check if there is a signal on the proximity switch between the reference point and the deceleration point during the reference process.
f.故障：已经使用一段时间，突然出现玻璃清洗出来不干净。原因：1、要检查水质是否干净，更换水。清理风机入口过滤网。2、如是为均匀的横条状，检查最后一道胶辊表面是否有赃物。3、如果表面是斜状痕迹，检查最后一道胶辊中间是否有缝隙，如有调正胶辊轴承座弹簧。
f. fault: the glass has been in use for a period of time and suddenly appears to be dirty after cleaning. reason: 1. check if the water quality is clean and replace the water. clean the filter screen at the fan inlet. 2. if it is a uniform horizontal strip, check if there are any dirt on the surface of the last rubber roller. 3. if there are oblique marks on the surface, check if there are gaps in the middle of the last rubber roller, and if there are any, adjust the bearing seat spring of the rubber roller.
g.故障：板压在压合过程中碎玻璃。原因：板压压合过程当中碎玻璃有很多因素，要根据实际状况来找原因。主要几个因素有以下几种：1、吸盘吸不住玻璃。调整控制吸盘的气压至7-8mpa，检查与玻璃接触的吸盘是否工作，如不工作为调整电磁阀和相应吸盘的微动开关。2、液压压力过大。调整液压压力。3、板压前后压板不平行。调整前压板。4、板压内有高点，主要是有胶或别的异物。清理。
g. fault: the board is crushed with glass during the pressing process. reason: there are many factors affecting the broken glass during the pressing process of the board, and it is necessary to find the cause based on the actual situation. the main factors are as follows: 1. the suction cup cannot hold the glass. adjust the air pressure of the control suction cup to 7-8mpa, check whether the suction cup in contact with the glass is working. if it does not work, adjust the solenoid valve and the corresponding micro switch of the suction cup. 2. excessive hydraulic pressure. adjust the hydraulic pressure. 3. the pressure plates before and after pressing are not parallel. adjust the front pressure plate. 4. there are high points inside the plate pressure, mainly due to adhesive or other foreign objects. cleaning.
h.故障：玻璃错位。原因：玻璃出现错位现象主要是因为玻璃大小或速度的改变造成玻璃没有碰到定位。调整触摸屏内延时时间。如是1600生产线，调整变频器减速时间。
h. fault: the glass is misaligned. reason: the phenomenon of glass misalignment is mainly due to changes in glass size or speed that cause the glass to not touch the positioning. adjust the delay time within the touch screen. for the 1600 production line, adjust the deceleration time of the frequency converter.
中空玻璃 与中空百叶玻璃
中空玻璃与中空百叶玻璃，作为现代建筑中常见的建材，具有许多优点。它们不仅在隔热 隔音和安全性方面更胜一筹，而且还能提供舒适的室内环境。本文将对中空玻璃与中空百叶玻璃进行深入解析，并 它们的其他相关内容，带你全方位了解这两种产品。.中空玻璃中空玻璃是由两片玻璃之间通过铝合金或塑料制成的边框密封而成的。...
中空双层玻璃
中空双层玻璃是一种常用于建筑玻璃中的新型材料，其结构独特，具有诸多优势。本文将就中空双层玻璃的特点 使用场景及优势展开详细解析，同时 其衍生的相关内容，以期为读者提供丰富且有创意的文章。.中空双层玻璃的特点中空双层玻璃由两层玻璃之间以特殊密封方式保持一定距离形成，形成中间的气腔。这一设计可以有效隔绝...
中空普通玻璃
中空普通玻璃是一种常见的建筑材料，具有很好的隔热 隔音和防水功能。它由两片玻璃之间的空气层组成，通过特殊的工艺将两片玻璃固定在一起，形成一个中空的结构。中空普通玻璃不仅在建筑领域广泛应用，也被用于汽车 家电等行业。.隔热功能 中空普通玻璃的空气层具有很好的隔热性能，能够有效阻挡热量的传导。在夏季，中...